Pool care Tips

 

PoolCare

10 Great tips for your Pool!

 1: Open Your Pool for Swimming Season

Maintaining your pool year-round will save you some sweat come swimming season.

If a pool is properly winterized, it can easily be reopened come swimming season. Most importantly, don't remove the pool cover until you've cleaned the area around the pool. Sweep or hose away debris to prevent it from getting into the pool. Next, use a garden hose to fill the pool to its normal water level. Reconnect everything that was disconnected. Water will need to flow through the circulation system, so open the skimmer line valve. Test the water for its pH level, then shock the pool. It'll take a week or more before the pool gets balanced and becomes swimmable. Leave the pump running 24 hours a day, and reduce the run by only an hour or two each day until the water is balanced.

2: Winterize Your Pool

Where you live determines whether or not you should winterize your pool. If your location experiences temperatures that drop below freezing, you'll need to take steps to ensure that your pool stays healthy. Residual pool water left in pipes can freeze and cause damage. To prevent this from happening, use an air compressor to blow water out of the pool's plumbing when swimming season is over. Also, drain as much water as possible from the filter and heater. Any remaining water can be eliminated using nontoxic antifreeze (caution: this is different from antifreeze for vehicles). Disconnect the heater, pump and chemical feeders, the latter of which should be cleaned and stored.

Finally, clean the pool: skim, brush walls, vacuum, empty skimmer baskets, close skimmer line valve, lower water level to approximately 45 centimeters below the coping and supercholorinate. Lastly, cover the pool to keep out debris.

3: Find and Repair Leaks

You don't have to get too high-tech to test water levels.

Sometimes it's difficult to determine if low water levels are due to evaporation or a leak. You can discover leaks in your pool by conducting a simple bucket test. Fill a plastic bucket three-quarters full of water. On the inside of the bucket, mark the water line. Place the bucket in the pool, then mark the water line on the outside of the container. (If the bucket has a handle, remove it to allow for better stability while floating.) Let it float for two or three days. If the water inside and outside the bucket has gone down the same amount, your pool is losing water due to evaporation. However, if the pool water level has gone down more than the water inside the bucket, your pool has a leak. That's your cue to call a professional to have it patched.

4: Supercholorinate Water

Organic contaminants like ammonia or nitrogen build up in a pool over time. Massive amounts of such contaminants can interact with a pool's chlorine to form chloramines, which give off that potent chlorine smell that many people associate with pools. To get rid of this harsh odor, it's necessary to superchlorinate -- or shock -- pool water back to normal chlorine levels. While it may seem counterintuitive, adding a large amount of chlorine to a pool can make the undesired odor go away. Some pools should be shocked once a week, while others can go a significantly longer time. Follow manufacturers' instructions before superchlorinating your pool to get the best results.

5: Maintain the pH Level

Testing your pool's pH level is as simple as dipping a strip of paper in the water.

Pool water should be tested regularly to make sure it's clean and healthy. The pH scale is a measurement of acidity or alkalinity that runs from 0 to 14. A reading between 7.2 and 7.8 is ideal; this range is safe for swimmers and helps sanitizers work at top efficiency.

You can monitor your pool's pH level with a testing kit. There are many kinds of testing kits available; however, most homeowner versions are either reagent kits or test-strips. Reagent kits aren't too difficult to use. You take a sample of pool water, then add liquids or tablets to it. The water changes color, indicating its chemical balance. Test-strips work differently. When you submerge them in the pool for a few seconds, dyes they contain cause them to change color. Next, match up the strip to a color chart to determine the pool's pH level. Use this information to gauge what kind and how much of the chemicals your pool needs.

Next Page